Selecteer het land/de regio, de taal en de valuta van uw voorkeur om te winkelen.
VEVOR Metaaldraaibank 17,8 x 40,6 cm Metaaldraaibank 50-2500 tpm Tafeldraaibank 800 W 9x Metrisch (van 0,5 tot 3 mm) 10x Inch (van 10 tot 44 TPI) Draad MT5 Spindelconus

Klantbeoordelingen voor VEVOR Metaaldraaibank 17,8 x 40,6 cm Metaaldraaibank 50-2500 tpm Tafeldraaibank 800 W 9x Metrisch (van 0,5 tot 3 mm) 10x Inch (van 10 tot 44 TPI) Draad MT5 Spindelconus

178x406 mm 1000W

klanten-reviews

Hoe werken klantbeoordelingen en -ratings?
Klantrecensies, inclusief productsterrenbeoordelingen, helpen klanten meer te weten te komen over het product en te beslissen of het het juiste product voor hen is.
Onze eindscore is geen simpel gemiddelde. We geven prioriteit aan authentieke, betrouwbare beoordelingen en filteren duplicaten of ongeldige inhoud eruit voordat we de eindscore berekenen. Dit zorgt ervoor dat de score de werkelijke ervaringen van klanten goed weergeeft.
Beoordeel dit product
Deel uw mening met andere klanten.
Schrijf een recensie
60 Beoordelingen
Beoordelingen voor het Huidige Artikel
Geverifieerde aankoop
Alleen foto's en video's
GEFILTERD OP
Geverifieerde aankoop Wis filters
60 beoordelingen
Vertaal alle recensies naar Nederlands
Vertaald
Zie origineel
Jean-Marie Desclin Jean-Marie Desclin
Particulier
178x406 mm 1000W
Super pour le prix et pour débuter.dommage aucune explication, un petit fascicule en anglais..... Rien concernant le changement des pignons, ni le réglage des outils, les points de graissage....etc....
2 mensen vonden dit nuttig
Vertaal de recensie naar Nederlands
Vertaald uit Frans
Zie origineel
Ray Ray
owner
owner 4 owner 4
Great machine Mechanically for the price, just the electronics that have let it down, it was going good until it suddenly went bang and smoke coming from the rear, on investigation I found 2 capacitators and the rectifier had blown, so rather having a lot of back and foreword Emails I ordered new ones, which I hope will fix it, Should this not work maybe you could supply a new Board ?
5 mensen vonden dit nuttig
Vertaal de recensie naar Nederlands
Vertaald uit Engels
Zie origineel
Francis Francis
M.
Nice little machine. Don't buy for making threads. Most of the gear combinations shown on the chart are impossible to do (0.50, 0.75, 1.00, 1.25, 1.50, 10, 11, 20, 28, 38, 40 and 44). Two of them need 44 and 70 tooth gears witch are not included (11 and 38).
2 mensen vonden dit nuttig
Vertaal de recensie naar Nederlands
Vertaald uit Engels
Zie origineel
Andre Andre
Good with some love and upgrades
Overall a good machine. The gibs are not easy to adjust right, especially on the x axis. The tail piece fit is poor. But with some love, it can be made to work fine. For the price, a good machine if you are willing to work on it.
0 mensen vonden dit nuttig
Vertaal de recensie naar Nederlands
Vertaald uit Engels
Zie origineel
Chris Olson Chris Olson
Mr
Good power for turning most metals. Quick setup and operational in no time. Little to no runout on the chuck.
4 mensen vonden dit nuttig
Vertaal de recensie naar Nederlands
Vertaald uit Engels
Zie origineel
RONALD RONALD
Hobbyisr
It is a nice metal lathe. the only disregard I can find is it doesn't have any clearance for the power feed screw and it does have an Off/On Switch.
0 mensen vonden dit nuttig
Vertaal de recensie naar Nederlands
Vertaald uit Engels
Zie origineel
Joel Joel
I wish I'd known this before buying
Before buying I did my due diligence, read reviews and watched lots of youtube videos, so I though I knew pretty all I needed to know about this lathe. However, one thing I didn't know was that even though the thru-lathe bore is 32mm, the bore of the chuck is only about 20mm (I didn't measure it exactly)... Therefore, if you're counting on using the thru-bore to turn long pieces, know that you're limited to about 20mm in diameter with this chuck. If you're planning on machining something bigger that way, you'll need to either buy (and fit) a bigger chuck, a collet chuck or some alternative way of mounting your piece. VEVOR should mention this in the description because it misleads people (like me...) into thinking they're gonna be able use the thru-lathe bore on pieces up to 32mm in diameter...
9 mensen vonden dit nuttig
Vertaal de recensie naar Nederlands
Vertaald uit Engels
Zie origineel
hp hp
King
Very quick delivery! Well packaged and the machine arrived without damage. Overall build quality is very good. It runs reasonably quiet all the way up to a displayed 2500rpm. The feed-lever engagement is not very solid, will see how it performs when I start using the machine.
0 mensen vonden dit nuttig
Vertaal de recensie naar Nederlands
Vertaald uit Engels
Zie origineel
carl carl
178x406 mm 1000W
De gebruiker heeft geen schriftelijke opmerkingen achtergelaten.
0 mensen vonden dit nuttig
Vertaal de recensie naar Nederlands
Vertaald uit Engels
Zie origineel
Martin Fooks Martin Fooks
Mini Lathe - Vastly underpowered
178x406 mm 1000W
Save your hard earned cash, spend a bit more and buy a much better lathe (unless you only plan to turn wood or plastic!)
2 mensen vonden dit nuttig
Antwoord van de klantenservice: We have received your ticket regarding this issue. Our customer support team will follow up on your problem within 24 hours and continue assisting until all your needs are resolved. Please keep an eye on the ticket responses and email notifications.
Vertaal de recensie naar Nederlands
Vertaald uit Engels
Zie origineel

Mensen die dit artikel kochten, kochten ook