Klantbeoordelingen voor VEVOR Diktebank, Twee messen, 330 mm brede werktafel, Schaafmachine, 1800 W, Schaafmachine, 23.500 tpm, Dubbele rollen, Rollover-beveiliging, Eén snelheid Houtbewerking, Voor hard en zacht hout

Sehr schlechte Qualität vom Hobel Ergebnis. Macht sehr tiefe riefen im Holz, dafür braucht man keinen Hobel. Der Service von Vevor ist schlecht, reagiert nicht auf Mails. Habe jetzt den Zahlungsdienstleister eingeschaltet. Nie wieder VEVOR

You would think a company as large as VEVOR, who has sold countless amounts of equipment to myself and others would stand behind their product when the item is defective. Not only does VEVOR make it nearly impossible to locate return information, when you do find it they fight you instead of resolving the issue. NEVER AGAIN VEVOR!!

Nie polecam zakupów, Przy próbie zwrotu towaru okazało się to całkowicie niemożliwe.

La table descend très difficilement et plus on descend plus c'est dur mauvaise ajustements des coulisseaux et j'ai choisi un arbre à pastille et je le regrette car la finition du remontage et le montable on voit chaque marque de pastille il faut tout poncer après Seul avantage dépasser si on prend un clou on n'a pas toute la lame à changer mais la finition est vraiment lamentable et aucun réglage possible

Para ser la primera herramienta que les he comprado ,estoy un poco desilusionado por como ha llegado golpea y doblada la chapa.

Contacted the customer service first in two ways, and I gave them one week to reply; nothing so far, so I must come out with the negative review. Firstly, I also ordered the three-blade version with two speeds 5 days ago, but it hasn't yet arrived. - This Spiral-Style Cutterhead is an absolute abomination. The finish that comes from this doesn't change if you try to swap the blades or reinstall them. Also, they can be turned around only once, with two cutting edges, not four, and they don't sell new blades, and they are made of the same steel, so it will increase the cost of a full change in comparison to a 2-3 blade one. This finish is worse than any normal 2-3 blade machine could give; it also chips against the grain the same way as "normal" blades. Leveling the table 100% isn't possible, so for anti-snipe, you must build your own base from MDF/plywood that is 100% flat, which will eat 20-35mm of height capacity. Same for most tabletop planers, some have a better quality base to calibrate flat. Waiting to get my return information and money back. So far, no reply. Previously, customer service was prompt when I had an issue, and it was solved immediately. Oak board on the picture, did the same with pine, and sanding double the normal with Festool won't fix this even.

A megrendelt gyalut most használtam először 1 m deszkákat gyalultam vele az első 8 db deszka nagyon szépen le gyalulta utána 2db kés kieset a csavar feje le eset amivel rögzítve volt a kés.

When the Wood plate is rough the machine pulls the plate but when the plate is smooth it can't pull (it starts to slip)

On my first use the machine left linear grooves where some of the blades went deeper and some more superficial - required a great deal of sanding. The company has NO ACCESSIBLE CUSTOMER SERVICE. Technical support has no clue where I can get replacement blades for when these blades wear out.. i WILL NOT BUY FROM VEVOR AGAIN

Tried to use this thing. Cutting head makes and awful sound when lowering with the crank and couldn't even lower past 1 inch to plane boards. Assuming it's a manufacturing error. Cuts well though for the price though unfortunately can't use because of the poor crank.