Klantbeoordelingen voor VEVOR Handmatige tegelsnijder 35-1000 mm Tegelsnijder Verstelbare infraroodlasergeleider Tegelsnijmachine Precieze enkellijns tegelmachine Keramische tegelvloertegelsnijapparaat

Nicht zu vergleichen mit Profigeräten von Sigma,Kaufmann usw Bruchvorrichtung könnte besser sein manche Fliesen lassen sich nicht brechen da die Leitschiene sich durchbiegt Stahl wäre besser als Aluminium für den Heimwerker reicht es aber aus.

Flexes on the snap and score on long runs. Hard to compensate for the variance in accuracy

Appareil lui même très bien mais la barre supérieure est trop souple

Ότι καλύτερο έχω χρησιμοποιήσει στην δική μου ζωή με αξιοπρέπεια και σεβασμό στην παράδοση και την πορτα να μου βρεις βιντεο για την υγεία

maszynka duża masywna z podpprkami to na plus. podstawa dziwnie się wygina tak nie naturalnie. Cięzko ustawić laser. Cięzko wyczuć z jaka siłą naciskac na ramie. Za lekko płytka się krzywo złamie. Jak zamocno to tnie krzywo. Drugi raz bym nie kupił Byc może nie umiem tego obsugiwać. ;)

Zawiodłem się, liczyłem na lepsza jakości, przecinarka się wygina, na dodatek na środku źle docina, a czasami przy gresie 7 mm raczka opiera się na prowadnicy i nie idzie noża docisnąć bo palce przeszkadzają, ustawiałem na różnych podłożach, efekt ten sam szczególnie prze mniejszych rozmiarach płytek typu 30cm 40cm

Came partially assembled one of the side support legs wasn't installed and in order to install it needs to be disassembled , bearings not one was spinning freely because the washers were installed at the front of the spacers onto the bearings and that was stopping them from spinning so again need to be switched around so basically complete disassemble to fix this issues then the laser is not 4 screw adjustable only two and is impossible to align it if the back aligned to the cutting wheel then the front at least 1/8" off if the front aligned then 1.5 " at the back is off I tried for an hour and not possible to align it , the breaker shoe doesn't have a magnet to hold it up when you score so it's a bit annoying, I am disappointed!

Envio fora de prazo e sem rastreio. A máquina de corte de cerâmica manual chegou com defeito nas borrachas dos apoios laterais, enviei fotos da situação e estou a aguardar que enviem substituição da peça com defeito.

Für gelegenliches schneiden der fliesen , mit reichlicher zeit wird der fliesenschneider reichen , das schneiderad ist leider etwas zu hoch für die fliesen , es hätte ruchig tiefer sein können .

For the price the quality is fine, but it does have some flaws that keep me from using it on a daily basis. 1. The piece that has to snap the tile after scoring can not be held up, so it’s always hanging in the way when cutting. That is quite annoying if you’re trying to cut precisely. 2. The laser attached is basically useless, since it doesn’t have enough options to calibrate it to be precise/usable. It can only be rotated, not moved from left to right. 3. Also the guide or “tile stop” is totally out of square, so basically unusable. 4. The ad claimed it has a carbide roller blade, but it doesn’t have it. So it dulls very quickly, had to buy a real carbide blade separately. A few minor tweaks could have made it way better, but they chose not to which is disappointing.