Klantbeoordelingen voor VEVOR Handmatige Tegelsnijmachine 35-600 mm, Tegelsnijmachine, Tegelsnijder Snijdikte 6-15 mm, Extra Snijwiel, Keramische Vloertegelsnijder, Laserpositionering, Enkelspoor 6 kg

Para cortar azulejos pequeños supongo que sirve. Los de 120 no los corta bien.

I bought the 47 inch tile cutter about 2 months ago and have done one project with it. I found the laser light useful particularly as the built in square on the tool was not square. The roller cutter was smooth and cut cleanly. There was flex in the base so one had to ensure it was on a solid table. I would not recommend this tile cutter for extended use as it required more measuring because of the out of square guide.

This was of some use for a while but it doesn’t cut accurately and the rails are weak and flex, look, you get what you pay for but I wouldn’t buy another one and ended up spending much more money on a descent tile cutter

I bought this to cut large format tiles, 24 x 48. I have several smaller cutters. The trend to larger tile sizes forced me to get a new bigger one. The packaging looks good on the outside. However when I set it up and started using it I quickly realized it was going to be a challenge to get the job done correctly. One of the biggest gripes I have is they didn't calibrate the tool. There maybe a laser mounted on the head but as is out of the box it's useless. You will need to adjust it. Then I put a tile in and scored it, pressing the snap bar separated the two halves. pull it out from the bed and how off square could it be? Try 1/8" per foot. That is ridiculous. The rails seem too thin for the length that they are. The car slides nicely. There are these wings on the sides to support tile overhang. They are flimsy are get in the way if you're not using them. The unit is put together with nylock bolts and screws. Put aside 3 hours to setup and calibrate. It's not ready to use as is out of the box. Would look elsewhere for a more robust accurate tool.

Dwa tygodnie temu zakupiłem taką maszynę gdzieś widziałem jakieś błędny filmik czy konstrukcja jest naprawdę solidna. Moim zdaniem Górny profil w ogóle nie nadaje się do czegoś takiego ugina się. Nie polecam szkoda pieniędzy.

I tried cutting three 48" tiles, but every single one failed. Had to return back to angle grinder cuts.

Belle longueur certes… aucun réglages corrects… équerrage pourri, laser pas droit bref assemblée en chine. Et les deux barres de guidage qui se courbent à chaque marquage de carreaux. Bref je suis très déçu. En plus je l’ai payé plus de 100€. J’aimerais un avoir ou être remboursé car le produit ne correspond pas du tout à mes attentes

Un peu déçu car la coupe avec des carreaux de 7mm (60 x 60 cm) d’épaisseur n’est régulière. De plus, le colis est arrivé ouvert dans le cheminement de livraison (DPD), il a été visité comme d’habitude.

Not stable then cutting, often makes curved cuts -3-5mm on the middle

Leider bin ich mit diesem Fliesenschneider (1200 mm) überhaupt nicht zufrieden. Wie auf den Fotos deutlich zu sehen ist, schneidet das Gerät nicht gerade – der Schnitt verläuft schief und macht einen starken Bogen. Selbst mit der Laserführung ist kein sauberer, gerader Schnitt möglich, da die Schienen bzw. die Führung zu ungenau sind. Für präzise Fliesenarbeiten ist der Schneider in diesem Zustand leider unbrauchbar. Sehr enttäuschend für ein Gerät, das als „Profi“ beworben wird.