Klantbeoordelingen voor VEVOR Draadsnijset Machinetappen 110-delig, Kerngatboor Draadsnijset Lagerstaal Machinedraadsnijset Inclusief 35 x Tappen, 35 x Stansen Draagtas Metrisch
110 pcs Metrisch
klanten-reviews
Hoe werken klantbeoordelingen en -ratings?
Klantrecensies, inclusief productsterrenbeoordelingen, helpen klanten meer te weten te komen over het product en te beslissen of het het juiste product voor hen is.
Onze eindscore is geen simpel gemiddelde. We geven prioriteit aan authentieke, betrouwbare beoordelingen en filteren duplicaten of ongeldige inhoud eruit voordat we de eindscore berekenen. Dit zorgt ervoor dat de score de werkelijke ervaringen van klanten goed weergeeft.
Beoordeel dit product
Deel uw mening met andere klanten.
Schrijf een recensie
293 Beoordelingen
Beoordelingen voor het Huidige Artikel
Geverifieerde aankoop
Alleen foto's en video's
Vertaal alle recensies naar Nederlands
Justyn Becker Just ok
110 pcs Metrisch
Had a die break on first use, they do not have the taper needed to get started. And a few common sizes found in automotive repair are not in the kit
0 mensen vonden dit nuttig
Vertaal de recensie naar Nederlands
Barry Chasers, not cutters
116 pcs Metrisch & imperiaal
Good for thread chasing but not good for thread creation / cutting. Nevertheless, good price for what they are
0 mensen vonden dit nuttig
Vertaal de recensie naar Nederlands
LD Storage box arrived damaged (courier?). Decent quality for the price.
116 pcs Metrisch & imperiaal
Comparing these to an SCA set I found the quality of the tools felt a bit lower, not a huge difference. You can tell by the size markings on individual taps and dies that they come from a range of factories which doesn't inspire confidence for quality control. The box looked good, but unfortunately it arrived damaged. Some of the pieces came loose during shipping and caused a couple of sections on the inside of the case to get cracked. Overall, not bad for the price, but they should secure the pieces better for shipping.
0 mensen vonden dit nuttig
Vertaal de recensie naar Nederlands
Anonymous Not the product I wanted.
110 pcs Metrisch
I wanted a tap and die set with SAR sizes. I bought this by mistake. They DON’T SELL a set with plug profile taps in SAE sizes.
0 mensen vonden dit nuttig
Vertaal de recensie naar Nederlands
Allen ocheltree Handyman
116 pcs Metrisch & imperiaal
Always using a tap or die. Bought because it was cheap. On opening it for the first time pieces fall right out and don't stay put. Only used once on a 1/4 20. No drill bit guide included. Good if your into cheap
0 mensen vonden dit nuttig
Vertaal de recensie naar Nederlands
Sean casey Mr
110 pcs Metrisch
I bought these and so far 4 have broken, the tap holders both get stuck and the taps aren’t held in very well, very poor quality,
0 mensen vonden dit nuttig
Vertaal de recensie naar Nederlands
Alex Tap and Die set
116 pcs Metrisch & imperiaal
I gave my ratings on this set based on receiving and viewing this set, I haven't physically used it yet, though if and when I do, I hope I can change my opinion.
0 mensen vonden dit nuttig
Vertaal de recensie naar Nederlands
ALEX CRUMPTON 50/50
116 pcs Metrisch & imperiaal
Half the taps and dies Don't work due to the machining of them being very poor, m10x1.5 die doesn't even fit a m10x1.5 thread and noticed a bunch of them are juat poorly machined and don't work
1 mensen vonden dit nuttig
Vertaal de recensie naar Nederlands
CrustyCal Sir
116 pcs Metrisch & imperiaal
A good range set for the money, if your a occasional user. The worst thing about it is the cheap plastic case. It doesn't hold the dies nor a good deal of the taps, so closing and opening is fraught with pieces flying all over the place. The tool handles are also cheap and loose their grip easily on the taps. Address those 2 shortcomings and it would score better
0 mensen vonden dit nuttig
Vertaal de recensie naar Nederlands
Jeff Worth the money
116 pcs Metrisch & imperiaal
Does the job i needed it for
0 mensen vonden dit nuttig
Vertaal de recensie naar Nederlands
