Klantbeoordelingen voor VEVOR Bouwventilator 255W AC-motor Bouwventilator 2830 RPM Bouwventilator Ventilator 1720 CFM (2922 m3/h) Axiale ventilator met 10 m slang Axiale ventilator 79 dB geluidsniveau Industriële ventilator

Purchased for home use - drywall & sanding. Very well built but a little heavy. Very powerful and draws air out with ease. A little noisy so wear ear muffs. The retractable plastic hose is strong and folds compact.

Je recommande ce produit très bien et très performant sert pour aspiration forcé dans un endroit clos lors de soudures. Petit point a améliorer; l 'accrochage de la gaine sur la ventilation.

Only the invoice is complicated, add a VAT number is not so logical, but we will get used to it.

Could I have invoice of this order ( 24111800942214460593), you can send my email info@nagroup.fi. I need invoice to our bookeeper. Thank you! BR Nicolas

Für den Preis unschlagbar. Wurde sehr schnell und in super zustand geliefert. Abzug bei den Sternen bekommt das Produkt da der Schlauch absolut nicht passt: 1. ist er instabil. wenn eine der Zwischenringe kippt wird keine Luft mehr angesaugt / ausgestoßen 2. Der Schlauch ist viel zu lange, wodurch die ganze Saugleistung verloren geht - egal ob der Ventilator aus dem Schlauch herauszieht oder durchbläst. Prinzipiell kann ich den Ventilator selbst empfehlen da der tut was er soll zu einem unschlagbaren Preis. Der Schlauch jedoch ist unbrauchbar.

Das Gerät ist schnell angekommen, macht, was es soll und sieht solide aus. Trotzdem wäre eine Rechnung ohne weitere Aufforderung zur Zusendung schön und ist buchungstechnisch in Deutschland notwendig.

The unit itself is ok, with a 10m hose connected doesn't have enough power to collect dust properly when cutting concrete. You either need a bigger unit with more power or use 2 units, one at the front and one at the back of the hose.

This turned out to be a good purchase. The fan feature works well,, the noise level is right at tolerable if you’re running it in the same location that you’re working in and the room size is a conventional room in a residence. If you’re running the fan on the opposite side of an exterior wall, it’s obviously more tolerable. As far as features, it’s hard to rate higher than a four, because there aren’t any features beyond the on/off switch and the GFCI reset switch. The fan draws enough air to clear smoke and Sheetrock dust effectively, as long as you’re providing enough air for it to move out. The fan is only set up to pull air at the end of the ventilation tubing and NOT PUSH IT, but I did have to utilize it as a push because of environmental circumstances and it performed ok as well with no detectable added strain to the motor. You just need to ensure that you tie the tubing to the fan casing well, because it’s not flanged like the intake, but it does have a rolled edge. I also secured around the guard for the trigger just to be certain it didn’t work itself free and blow the tubing through a window or something. The fan seems to be built well, but there’s not a whole lot of building involved. The casing is steel with rolled edges, intake is flared to connect tubing, functional GFCI switch inline, orange paint that helps with visibility, an on/off switch, removable steel grates on either end to facilitate cleaning and any maintenance or necessary repair, thick plastic fan blade and rubber feet for traction. You should be sure to clean as necessary, especially when you have it moving dust or things of that nature, and I had an old nylon bag that wasn’t being used to throw the tubing into, as well as a small leather belt that I got to run through the tubing and latch to make it easier to carry with the fan. Fan weighs 26.2 lbs carry weight total as I have it set up to travel, and depending on what I’m using it for, I usually keep a 13 gallon trash bag as well to put the vent tubing into until I can get home and rinse out any dust that may have accumulated inside.

Works fine, good quality but a speed control would have made it perfect!

Einfaches aber leistungsfähiges Gerät. Robust aufgebaut. Ich benutze es, um beim Schleifen oder Sägen in meiner Werkstatt den Staub abzusaugen, da ich keine feste Absauganlage habe. Das einzige Problem, das mir aufgefallen ist, besteht darin, dass es am Rand des Ansaugstutzens eine Verwirbelung gibt, die entgegen der Ansaugrichtung läuft, d.h. in einem kleinen Bereich um die Rundung scheint das Gerät zu blasen anstatt zu saugen das Gerät. Darauf sollte man bei der Aufstellung achten, damit anfallender Staub nicht in den Raum geblasen wird, anstatt abgesaugt zu werden.