Klantbeoordelingen voor VEVOR 58 cc benzinekettingzaag, 508 mm kettingzaag, krachtige zaag van 2,7 pk met antisliphandgreep, twee brandstoftanks en noodstopfunctie, max. 11.800 tpm voor houtkap, snoeien en ruimen van bomen

At first, I was impressed...until I got around to using it. First off, installing the bar to the saw...meh. Took a minute. Very cheezy set up. Felt like I was going to break the chain tensioner to get the chain tightened to my personal preference...just slack enough to read 2 pitch numbers pulling from the top of the bar. Second, the retaining nuts for the bar wont tighten enough no matter how much you tighten them again afraid I was going to break the studs off...because it feels cheap. Oh and one nut falls off while operating...no matter what! Using thin washers behind the nuts seemed to do the trick however. Not a fan of the "Ez start" You can't hold it with 1 hand and start it with the other! Impossible! LAME!!! Have to use your damn foot on the ground or squeeze it between your knees! No primer bulb no carb adjustments. Takes 5-8 pulls to start even when hot! BUY EXTRA CHAINS WITH YOUR ORDER! They dull quick but do sharpen well. I run Amsoil 100:1, non ethanol 91 or race gas 40/60 in all my 2 strokes. Dirt bikes, sleds, weed eaters and several chainsaws. I also rebuild all my motors and trust the 100:1 mixture 100%. I run 50: 1 and do a religious heat cycle break in procedure for the first 10 hours before I switch to 100:1. This saw was real boggy on the bottom end @ 50:1 for about 5 tanks then leveled out and seem to come around after about 3.5 hours of use. When I switched to 100:1...the saw came alive! WOW!!! It runs soooo good! Very powerful, very clean running, no bogging...but still takes 5-8 pulls to start! Lmfao! Have approx. 60 hours on the saw cutting only railroad ties for a huge retaining wall and 12 large railroad tie garden boxes. What I bought the saw for. The bar has held up flipped every 5 tanks but went through a dozen chains...I've gotten my money's worth 10 fold for sure!

Saw runs good and has plenty of power, but it leaks ALOT of bar oil EVERYWHERE!

The chainsaw seems like a good value for the price and has the features we were looking for. Unfortunately, ours arrived with the chain tensioning screw bent, which prevented us from properly tightening the chain and using the chainsaw as intended. I contacted VEVOR customer service about the issue, and they worked with me to provide a replacement. I appreciate their assistance, but I was disappointed that the chainsaw arrived with a defective part. Hopefully the replacement performs as expected.

Ran saw 3 times (1st day) went to start it for a 3rd time and the pull cord broke. Also the pull strings, cuts into the PLASTIC around the return hole. My big name saws have a metal cord guide inserted in the plastic housing instead of all plastic.

Starts bogging with extended use, good for small jobs but the longer u use it the more it starts to bog down

Very hard starting ! Should have primer bulb !

Great value for the money, and I'm impressed with its power. However, I have to sharpen the chain every time I use it, and I also have a hard time getting it started each time I want to use it. Other than those issues, it performs well for the price.

Was working good now has no spark can I return for a replacement chain saw

Just received my 62 cc Vevor chainsaw with a 20" bar. The wrench for the bar nuts is small and creates a tight area when trying to take the nuts off. The blade tensioner is in a poor location. I like that there's a storage area for the wrench, but its difficult to remove the wrench. The chain brake goes on from time to time without a reason to. This saw has a good weight and balance to it. The saw started fairly good and restarted great. The 62cc motor works well and this saw burns through logs extremely fast without bogging down. I was very impressed. I did also purchase the 3 year warranty, so I'll keep using this saw as much as I can.

Problème avec le livreur pas livré ou j'ai demandé