Klantbeoordelingen voor VEVOR 2x palletvorken klembaar 1490x100x230 mm vorkenbord 1814kg laadvermogen vorken 149cm totale lengte met 109,2cm vorkblad heftruck heftrucktanden voorlader palletframe

Bought with high hopes. The one pin to screw on isn’t screwing on properly. Needed a hammer in order to make it move. The forks wouldn’t stay on.

After installing these forks and using them for a while I have found them to be useful but really only because I only have a few things that require forks to lift. The most I am lifting are loads of about 500lbs. I must say that the fork itself feels very sturdy and they seem to be built like a tank. I say "seem" because unlike actual skid steer or similar forks these are made from rectangular box section rather than solid steel plate. Although they are heavy it is difficult to know the wall thickness of the box section and you are limited as to what you can pick up with these forks due to their very thick cross section. These forks will not fit under certain palettes. Again they have held up well with the loads I have lifted but I do not use palettes. These forks also stick out a long way in front of the bucket (in my case 60") and my bucket is 3 feet deep. That puts the load you are lifting a long way out in front of the skid steer and all of that load is being applied to only about 8 to 10 inches of the lip of the bucket. It really doesn't matter that they are rated for 4000lbs. The lip of the bucket will fail long before that 4000lbs could be lifted. The method by which they attach to the bucket is adequate for light loads but it is very difficult to attach the forks securely to the bucket. The large slot at the end of each fork slides over the lip edge of your bucket. Two "L" handle bolts on each fork fasten down on to the "lip" of the bucket clamping the forks in place. This is problematic for several reasons. First there are flared nut fittings that screw on to the ends of the "L" bolts where they clamp down on the bucket. One must be very careful to ensure these nuts have not travelled up the shaft of threaded "L" bolts while tightening. If they have it will be the sharp end of the "L" bolt that bites in to the surface of your bucket rather than the flared foot of the nut. Getting the "L" bolt tight enough while ensuring the flared nut is properly positioned to tighten against the bucket surface is difficult. Before I figured out that the flared nuts were NOT captive on the end of the "L" bolt, I had driven the end of one of the bolts half way through the surface of the metal clamping plate they give you to put between the bucket surface and the bolts. It is also difficult to tighten the "L" bolts enough to secure the forks in place. It is also important to install the forks over the bucket wear bands. This gives them something stronger to press against rather than just the sheet metal of the bucket. All in all these should be considered an inexpensive alternative to proper skid steer or tractor forks and only for light loads. I bought these because I could get them quickly and they allowed me to get my job done while waiting for my actual skid steer forks to arrive. Big difference between these at $175.00 vs. my skid steer forks at $2000.00.

I waited for a long time for the version with the stabilizer bar to become available for purchase and it never did. I reluctantly bought the ones without the stabilizer as they were needed sooner than later and thought I would just buy the stabilizer bar separately when it became available. A couple weeks later (of course) the set I originally wanted became available and I eagerly contacted Vevor for a stabilizer for my new forks, just to be told that it is not available for purchase separately and I should just sell this set of forks and buy a new set! Not impressed to say the least, one would expect parts and pieces/accessories of this nature to be available for your equipment down the line? We did come to an arrangement but I am still without my stabilizer bar I waited so long for. Do better please.

I purchased these 6 weeks ago. They arrived very quickly. The box was damaged. It looked like somebody taped part of a box over the original box. The parts bag was empty. It looked like somebody took the hardware out for a different set that was missing hardware and patched the box. It was missing all of the hardware to clamp to the bucket. Useless without it. I contacted customer support at least a dozen times. I get the run around. Parts are shipped. Parts are delayed. Please be patient. Here is a $15 credit. How about a $30 credit. I declined the credits as the forks are useless without the hardware, and I can't find the hardware that fits properly at the store. I have asked for a return several times, and keep getting different resolution options without getting me the hardware needed. I have asked that they take the hardware out of another box so that I can use the forks. Still no resolution. Frustrating.

Arrivé en 2 colis, les fourches dans un premier et le cadre avec les axes dans un second. L'acier semble solide et les soudures de qualité. Cependant, le matériel n'arrive pas avec les points de levage comme sur les photos du produits. J'ai donc du racheter ces elements en magasin afin de pouvoir l'utiliser en toute sécurité. Un point en moins egalement sur les points de fixation qui pourraient etre plus haut les 3 points qui descente parfois pas suffisamment: dans mon cas je suis tout juste si le terrain est plat et avec les bras au plus long.

Parts fairly heavy considering the cost. The pins to attach to 3 point hitch useless. It should come with proper boltst that attached to the 3 pt hit hitch. The bracket for that is weak point. If adding in cost to replace pins will not make it the good a price. If wanting to use with quick attachment bracket needs additional parts too. Somewhat satisfied.

Its hard to keep them for moving back and forth you can’t tighten them enough t on keep them from sliding under pressure

The bolt down clamps are way too cheap made. If you have a decent cutting edge on your machines bucket, it won’t clamp down enough

They ok not to good on your bucket..

I purchased these forks to lift pallets and other things on my Massey Ferg 1742 tractor. They work OK, but it is an absolute pain to get them attached and oriented properly, and despite my best efforts and strength, they will still shift under heavy loads. They are definitely built with solid metal, though the welds are not stellar. They weigh a lot, so be aware 1) when the package comes and 2) when you are fitting them. I absolutely HATE the 90 degree, 4 inch long arms on the top of the tightening bolts, because you sure as heck are not hand-tightening if you think you will keep the forks secure/in-place. After hand tightening, I have to use an open end wrench on the 90-degree and then a 1 1/4" open end to tighten the adjustment nut on the bottom before it has any chance of not moving (but it still will). Also, the stabilizer bar that goes between the forks is helpful, but when moving pallets it has to be all the way back to the stops, near the bucket, so it is only moderately useful. Overall, I am satisfied with the performance based on the cost, but don't kid yourselves (or watch the paid youtube reviews that make it look as smooth as silk), these forks are a challenge taking on/off and are not anywhere near as stable as a dedicated fork attachment.