Klantbeoordelingen voor VEVOR Papiersnijder SG-299A4 Papiersnijmachine 63,5 x 36,3 x 40,6 cm Papiersnijapparaat voor het snijden van papier Hefboomsnijder Poedercoating 45HRC Papiersnijapparaat

Taglierina A Leva Da 12" A4 300 Carte Taglierina Per Carta Ghigliottina Ufficio

Deze is niet fijn als je een stapel tegelijk wilt snijden. Gaat acheef en er zit geen vaste papier stiopper op dus je moet oppassen met schuiven

I purchased this item thinking it has a laser light on it. Lining up the paper to ensure the cut is a challenge. This item isn't working out the way I thought it would.

I purchased this because it was advertised as a heavy-duty paper cutter capable of cutting large stacks of paper. However, from the first time I attempted to use it, I noticed issues that made it unsuitable for my needs. The biggest problem is that the blade does not make a clean slicing cut. Instead, it pushes the paper forward as it cuts, causing the pages to lift, bend, and wrinkle. This happens even when cutting only a small number of sheets of 100gsm paper, nowhere near the advertised cutting capacity. There is also a measurement issue with the cutting guide. The printed grid does not line up in an intuitive way with the actual cutting position, as there is a gap between the ruler markings and where the blade cuts. This makes accurate measuring difficult and requires trial and error to work out the true cutting position. I have now tried to resolve these issues three separate times over the past year. When I first discovered the problem, I contacted VEVOR to request a return/refund, but the support I received was not helpful and the issue was not resolved. For a product marketed as a professional heavy-duty guillotine, I expected accurate measurements and a clean cut. Unfortunately, mine has never performed as expected and I cannot use it for the purpose I purchased it for.

I am just getting into book binding. Every book I have cut so far have about 300-400 pages. I have maxed it out once. The issue I have it that no matter how tight I crank it down, it always moves. Its nothing that makes a HUGE difference. If you want perfection I might not suggest this one to you. I don't mind. It is usually about 1-2 mm different between the top measurement and the bottom. I bet if I was doing something smaller it also would help.

Petit problème quand on coupe le début du papier et abîmé et pour régler la lame il n'y pas de réglage precis

Tout s'est très bien passé au début, coupe droite pas de soucis. Après avoir fait à peu près 200 découpe de papier 160 gr feuille à feuille, la lame semble émoussée, elle ne coupe plus sur toute la longueur mais déchire à certains endroits, et que dire de la tenue de la feuille, à chaque découpe la feuille n'est plus tenue (est-ce que c'est à cause de lame???) la feuille se déforme à chaque découpe, je fais des découpe pour un client et je me retrouve avec des feuilles déformée pas top au niveau de la qualité.

The blade detached within 3 months of occasional use. Never used it on over 250 pages, because that was when it started getting too hard to use. Used it less than 10 times a month. To get a replacement, I would’ve had to find a box big and strong enough to support it and take it to FedEx. Not feasible when you no longer have the original box and don’t own a car. This cutter is too big and heavy for one person to maneuver.

It came without instructions. That’s it. Period.

Not working properly after just 2 uses. It now pulls the stacks of paper inward puckering it against the metal board and it is leaving a .25 inch chunk eaten out of my chipboard that falls in the path of where the blade comes out. It is not a quality cutter if it doesn't work after 2 uses. I submitted a help ticket and it has now been 3 plus days with no solutions to the problem, requesting a refund. I would love to buy a stack cutter that actually works.